tag:blogger.com,1999:blog-6261993076995357307.post131245210281897382..comments2023-11-05T06:16:56.961-05:00Comments on the Carpentry Way: Mix and Match (III)Anonymoushttp://www.blogger.com/profile/14328401081765407624noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-6261993076995357307.post-25475664234022516162011-12-23T18:47:50.279-05:002011-12-23T18:47:50.279-05:00Brian,
everyone likes a good surprise. Thanks fo...Brian, <br /><br />everyone likes a good surprise. Thanks for your comment!<br /><br />~CAnonymoushttps://www.blogger.com/profile/14328401081765407624noreply@blogger.comtag:blogger.com,1999:blog-6261993076995357307.post-88111239999164155152011-12-23T18:20:01.340-05:002011-12-23T18:20:01.340-05:00Hhmmm....what could it be??!intriguing joinery aga...Hhmmm....what could it be??!intriguing joinery again Chris..<br />Brian Mulveybrianmhttps://www.blogger.com/profile/14193678225195676566noreply@blogger.comtag:blogger.com,1999:blog-6261993076995357307.post-66522058923196723142011-12-21T23:29:44.761-05:002011-12-21T23:29:44.761-05:00Paul,
thanks for your comment. I hope my plane w...Paul,<br /><br /><br />thanks for your comment. I hope my plane will not take this personally..<br /><br />~CAnonymoushttps://www.blogger.com/profile/14328401081765407624noreply@blogger.comtag:blogger.com,1999:blog-6261993076995357307.post-36623448279996927082011-12-21T10:45:01.177-05:002011-12-21T10:45:01.177-05:00I recently completed a project using Ipe. I talked...I recently completed a project using Ipe. I talked the builder into letting me buy and mill down Ipe as exterior trim for a large door. The trim "sorta" resembles the wainscotting of the buildings interior. I found it super hard but it finished very smooth. My block plane refuses to speak to me now.Paul Atzenweilerhttps://www.blogger.com/profile/02981296755785226132noreply@blogger.comtag:blogger.com,1999:blog-6261993076995357307.post-19287760250434424642011-12-20T21:23:44.526-05:002011-12-20T21:23:44.526-05:00Harlan,
thanks for your comment. I use a router w...Harlan,<br /><br />thanks for your comment. I use a router with an adjustable edge guide and 3/16" solid carbide spiral cutter. I use a pair of c-clamps and fasten the stick onto top of the plywood table top on my drill press. I use a second stick alongside to help balance the base of the router from tipping.<br /><br />~CAnonymoushttps://www.blogger.com/profile/14328401081765407624noreply@blogger.comtag:blogger.com,1999:blog-6261993076995357307.post-58795888548688928762011-12-20T19:03:04.478-05:002011-12-20T19:03:04.478-05:00I would be interested in the router set up used to...I would be interested in the router set up used to make those mortises. Whatever it is, it's looking good. <br /><br />Harlan BarnhartAnonymousnoreply@blogger.com